Altenburger 80.13.065 Dimmer (1channel) For Convent. Transf. 40-600va, Mdrc

Manufacturer-number: 80.13.065 - Phase-controlled push-dimmer, MDRC (1 Cannel, 40-600VA) With scene modulus (IBDA 600) The ALTODIM 600 is a plug-in module for DIN rail cabinets. If it receives EIB-telegrams it would control the connected load in a phase-control mode from 0 to maximum in its brightness. The device is suitable for the control of incandescent lamps, wire-wound transformers and electrical motors between 40 and 600 W/VA. The total load of the connected devices may not exceed the maximum load of the dimmer. In any case also the power dissipation of the transformers (approximately 15-20%) and of motors as well as their power factor has to be considered. The load ouput has an electronic current limiting in case of an exceeding of the maximal temperature. Additionally the control has an input for normal pushbuttons component has a pushbutton input for pushbuttons (230 V ~). This input can be used as an independent EIB-push-sensor. Several pushbuttons can be operated in parallel. The aforementioned functions are adjusted with the ETS software through the input of the respective parameters. Description of the component functions as it is pre-adjusted in the data base: After receipt of a 1-telegram (Object 0) the brightness jumps to that value which was set before the switch OFF function. A Status back indication would not be set. The brightness can be dimmed via object 1 and 2 within a range of 20% and 100%. For this procedure the dimmer requires approx. 3,2 secs. If the dimmer is switched OFF the switch ON function applies if the command dimming brighter of object 1 as well as with a value of object 2 is switched ON. The pushbutton input of the dimmer is pre-adjusted for the 1-push-switch/dim function. At a short touch of the pushbutton ( 400 ms) dimmer commands (object 4) are being sent. At a voltage return the brightness goes to the same level as before the voltage failure and the pushbutton input is kept synchronous to this value. All aforementioned parameters can be modified. Technical data EIB-supply Voltage : 24 V DC Load capacity : max. 230 mW at 29 V DC Extenal supply Voltage : 230 V~ 50/60 Hz Current : Note:Delivery costs and discounts are displayed clearly in the cart (click on icon cart symbol) depending on the currently selected payment methods, mode of shipment and value of goods as well as country and address. Phase-controlled push-dimmer, MDRC (1 Cannel, 40-600VA) Without scene modulus (IBDA 600) The ALTODIM 600 is a plug-in module for DIN rail cabinets. If it receives EIB-telegrams it would control the connected load in a phase-control mode from 0 to maximum in its brightness. The device is suitable for the control of incandescent lamps, wire-wound transformers and electrical motors between 40 and 600 W/VA. The total load of the connected devices may not exceed the maximum load of the dimmer. In any case also the power dissipation of the transformers (approximately 15-20%) and of motors as well as their power factor has to be considered. The load ouput has an electronic current limiting in case of an exceeding of the maximal temperature. Additionally the control has an input for normal pushbuttons component has a pushbutton input for pushbuttons (230 V ~). This input can be used as an independent EIB-push-sensor. Several pushbuttons can be operated in parallel. The aforementioned functions are adjusted with the ETS software through the input of the respective parameters. Description of the component functions as it is pre-adjusted in the data base: After receipt of a 1-telegram (Object 0) the brightness jumps to that value which was set before the switch OFF function. A Status back indication would not be set. The brightness can be dimmed via object 1 and 2 within a range of 20% and 100 - 80.13.065