Altenburger 80.13.062 Phase-Controlled Pushdimmer Convent. Transformer 60-1300w/va

Manufacturer-number: 80.13.062 - Phase-controlled pushdimmer, MDRC (1 Channel, 60-1300VA) With scene modulus (IBDA 1300-0/P) The ALTODIM 1300-0/P is a plug-in module for DIN rail cabinets. If it receives EIBtelegrams it would control the connected Ioad in a phase-control mode from 0 to maximum of the brightness. The device is suitable for the control of incandescent lamps, wire-wound transformers and electrical motors between 60 and 1300 WNA. The total Ioad of the connected devices may not exceed the maximum Ioad of the dimmer. In any case also the power dissipation of the transformers (approximately 15-20%) and of motors as well as their power factor has to be considered. The Ioad ouput has an electronic current limiting in case of an exceeding of the maximal temperature. Additionally the control has an input for common pushbuttons (230 V ~). This input can be used as an independent EIB-push-sensor. Several pushbuttons can be operated in parallel. Description of the component functions as they are pre-adjusted in the data base: After receipt of a "1-telegram (object 0) the brightness jumps to that value which was set before the switch "OFF function. A Status back indication would not be set. The brightness can be dimmed via object 1 and 2 within a range of 0% and 100%. For this procedure the dimmer requires approx. 3,2 sec. If the dimmer is switched "OFF" the switch "ON function applies if the command dimming brighter of object 1 as well as with a value of object 2 is switched "ON. The pushbutton input of the dimmer is pre-adjusted for the 1-push-switch/dim function. At a short touch of the pushbutton ( 400 ms) dimmer commands (object 4) are being sent. At a voltage return the brightness goes to the same level as before the voltage failure and the pushbutton input is kept synchronous to this value. Technical data Voltage : 24V DC (+6 / -4V) Input : max. 230mW at 29 V DC External supply Voltage : 230V~ 50 Hz Own consumption : Note:Delivery costs and discounts are displayed clearly in the cart (click on icon cart symbol) depending on the currently selected payment methods, mode of shipment and value of goods as well as country and address. Phase-controlled pushdimmer, MDRC (1 Channel, 60-1300VA) Without scene modulus (IBDA 1300) The ALTODIM 1300 is a plug-in module for DIN rail cabinets. If it receives EIBtelegrams it would control the connected Ioad in a phase-control mode from 0 to maximum of the brightness. The device is suitable for the control of incandescent lamps, wire-wound transformers and electrical motors between 60 and 1300 WNA. The total Ioad of the connected devices may not exceed the maximum Ioad of the dimmer. In any case also the power dissipation of the transformers (approximately 15-20%) and of motors as well as their power factor has to be considered. The Ioad ouput has an electronic current limiting in case of an exceeding of the maximal temperature. Additionally the control has an input for common pushbuttons (230 V ~). This input can be used as an independent EIB-push-sensor. Several pushbuttons can be operated in parallel. Description of the component functions as they are pre-adjusted in the data base: After receipt of a "1-telegram (object 0) the brightness jumps to that value which was set before the switch "OFF function. A Status back indication would not be set. The brightness can be dimmed via object 1 and 2 within a range of 0% and 100%. For this procedure the dimmer requires approx. 3,2 sec. If the dimmer is switched "OFF" the switch "ON function applies if the command dimming brighter of object 1 as well as with a value of object 2 is switched "ON. The pushbutton input of the dimmer is pre-adjusted for the 1-push-switch/dim function. At a short touch of the pushbutton ( 4 - 80.13.062